Manuals are also something that you can obtain with the help of our website. Remove the screw 7 , rubber washer 8 and locknut 10 and the clamp 9 that attaches the bottom of the lower fairing to the engine guard and set aside. As well, on our site you may read manuals and diverse art eBooks online, or load their. Carefully place one lower fairing in position from behind the engine guard. Fit the locknut and front ball joint left hand thread to the front of the quickshifter assembly Screw the locknut and ball joint on to the quickshifter assembly to achieve a dimension between the ball joint ends of 203.
Remove upper screws that attach the chrome headlamp nacelle to the front forks. Proceed to For All Models section. Left-hand and right-hand descriptions of the machines and their component parts refer to the right and left of a given machine when the rider is seated normally. If motorcycle is frequently used for trips less than 15 mi 24 km , in ambient temperatures below 60 °F 16 °C , reduce oil change intervals to 1500 mi 2400 km. Restricted movement could affect handling, resulting in personal injury. If the engine is not run frequently and allowed to thoroughly warm up, this water will accumulate, mix with the engine oil and form a sludge that is harmful to the engine.
Repair categories for other on-road vehicles that require mechanic certification to perform repairs are: a Motorcycle; b Recreational Trailer. If you removed the left hand pivot arm assembly, remount it now, 10002575-A pg 20 with seal, bearings 2 , washer, nut, cotter pin and dust cover. Register a Free 1 month Trial Account. Remove the front and rear ball joints and front locknut only from the gear selector rod. The problem is that once you have gotten your nifty new product, the harley street glide service manual 2012 gets a brief glance, maybe a once over, but it often tends to get discarded or lost with the original packaging. Install the intake manifold hold-down bolts We offer an Intake Manifold Bolt Kit 8504 that includes small-head silver Cadmium-plated bolts and matching hardened washers. Service Manuals; Mirrors 24 Mirror Sets; Single Mirrors; Seats 108 For all your 2012 Harley-Davidson Street Glide Street Street.
Remove the cable strap holding the clutch cable to the engine guard. Automobile and Light Truck Certification Categories. If have necessity to load pdf Harley street glide service manual 2012, then you have come on to the loyal website. Never scrape the windshield with a razor blade or other sharp instruments because permanent damage will result. Note: The ball joint and locknut on the transmission linkage have a left hand thread. Retain the gear selector rod if the motorcycle is to be returned to its original condition. Colors listed as Pearl or Metallic M have a clearcoat top coat finish.
Lexan®is a more durable and distortion-resistant material than other types of motorcycle windshield material, but still requires attention and care to maintain. Attach the upper docking bushings 22 using washer 21 and mushroom head screws 20 Use Loctite 242 blue on screw threads. Snug up the bolts evenly, make sure the end caps are not crooked in relation to the frame. As a result, the hands seen in the photographs are those of the author. If you want to use a windshield protectant on your windshield, try Harley Glaze Polish and Sealant®. Tighten all three screws to 15-20 ft-lbs 20.
Harley Davidson Service Manuals are available for immediate download. Immediately upon payment you will automatically be forwarded to our secure download page and at the same time we will send you an email with a copy of your Harley Davidson backup service manual download link. Remove the two black screws 1 that attach the fairing cap 2 to the lower fairing 5. This website is not associated with any product manufacturer mentioned in any way. They will damage the windshield surface. Make sure the end cap is seated properly. If positive + cable should contact ground with negative - cable connected, the resulting sparks can cause a battery explosion, which could result in death or serious injury.
Tighten to 12 ft-lbs 16. Align and attach velcro strips from kit to top, bottom and sides of compartment so they match the placement of velcro strips on pouch. Harley-Davidson Motorcycle Service Manuals Please visit our to see a complete list of all the backup service manuals we offer. Harley Davidson Flhx Street Glide 2012 Repair Service Manual can be very useful guide, and harley davidson flhx street glide 2012 repair service manual play an important role in your products. We constantly work on improving our services and making sure that all the links work properly and nothing can spoil your enjoyment. Further tightening will be required after the toe in is set.
Remove the seat following the instructions in the appropriate Service Manual. Firmly press the windshield into place until seated on docking bushings. Each of the six Chapters is divided into numbered Sections. Always keep the cooler clean and free from dirt and debris. Install the retainer 4 in position on the U-bolt and secure to the engine guard with the two locknuts 3.
Install the lower fairings following the instructions in the appropriate Service Manual. You can pay for your Harley Davidson backup service manual with Paypal or Visa, MasterCard or Discover. Remove the plastic end caps from the quickshifter assembly. Set the parts aside for re-installation. Park facing the sun, place an opaque object over the instruments, or adjust the windshield to avoid reflections. Finger tighten the locknut at this stage. T he respective headings can be entered in the list of contents.
Harley Street Glide Service Manual 2012 If you are searching for a book Harley street glide service manual 2012 in pdf form, then you've come to the correct website. Machined ring, left hand thread identification StreetTriple and Street Triple R 6. We offer the street legal version with high flow catalytic converter and open system for race track use only. For Models without Lower Fairings 1. Motorcycles with a Twin Cam 103 or larger engine are equipped with a factory installed oil cooler.