Do not use the system with any product that Philips does not recognize as compatible with the system. In the neutral position, the tip is straight when the indicators on the control wheels are aligned and point toward the center of the array rotation button. Press Review and if necessary, click Patient Directory. As with any array movement, the motor makes a humming sound while calibrating. Return to Installation Procedure List. Click the Manage Setups tab Figure 16-1. Slide the enclosure off the disk bay housing.
Prepare the pallet and ramp for sys- tem crating. It needs only to be plugged into the wall socket with the circuit breaker on. Place the ramp as shown with the beveled edge facing up. To remove all text, press the Erase Text key. If it is necessary to dry the transducer's lens after cleaning, use a soft cloth and a blotting motion instead of a wiping motion. Grip the module by the sides, and center the module so that it latches. Have the Network Administrator fill out the Connectivity Worksheet Table 5-7 prior to installation.
To increase cart security, use wheel chocks when the system is parked. Select a transducer and a preset. Remove the foam and corrugated braces from the top of the system. Indicates that interference may occur in the vicinity of equipment marked with this symbol. Lock the articulation arm before moving the system. Turn on the printer, and then turn on the system. Enter the numerical code from Table 5-4 to enter the settings listed.
All internal adjustments and replacements must be made by a qualified Philips Ultrasound field service engineer. Indicates the temperature range noncondensing for transport and storage. In that case, the system must be disposed of as biohazardous material in accordance with local or federal laws. In iE33 User Manual 4535 616 23901. Return to Installation Procedure List. The number of focal zones may iE33 User Manual 4535 616 23901. To Cover tabs remove the filter door cover, grasp the bottom and gently pull outward.
The cables and transducer bodies are liquid-tight, but the connectors are not. To remove or replace the iE33 system enclosures 1. Suggested intervals are 50 patient exams or 50% hard drive capacity. The devices can be installed in the peripheral bay for access from either the right or left side of the system. Please contact your local Philips representative for assistance. Remove the six panhead screws securing the left and right brake Right brake pedal extension cover pedal extension covers.
Touch screen controls include buttons and knob displays. The available presets are determined by the selected transducer. Preventing Tip Fold-Over The following steps can prevent the tip from folding over. Installing the Ergonomic Grip 1. Rear Panel Audio, video, and network receptacles Pull door to open Power switch iE33 User Manual 4535 616 23901.
Rewind the tape to the beginning of the current recording. In water, there is almost iE33 User Manual 4535 616 23901. Select the appropriate Define Query options as defined by the customer. Click the arrow to expand. Adjust the control panel articulation trigger-release tension Figure 7-7. Connector Illustrations Figure 11-1 Front Panel Connector Locations Frontplane Assembly J501, 0.
Remove the ten knobs covering the touch screen bezel. Remove the panhead screw on the right side of the rear disk bay enclo- sure. Place the ramp in front of the system with the beveled edge facing up. Natural rubber latex is not used on any Philips ultrasound transducer. Refer to the System Adminis- tration section of the iE33 User Reference. Place any boxed manuals, cables, or other items around the system on the pallet surface.
To match the look of the system display to earlier iE33 systems with the 43-cm 17-inch monitor, set Monitor to 2. Always use the cable management system to prevent cables from being stepped on or run over by the cart wheels. It transfers signal path data transactions, transducer tables, and other data. Type f and press Enter. S-Video connection iE33 User Manual 4535 616 23901. Remove the two panhead screws securing the upper front panel enclo- sure. If there are no spares, rein- stall dry and cleaned filters.