Replace belts if they begin to slip from wear. Do not put hands or feet near or under rotating parts. Handle fuel with care; it is highly flammable Keep clear of the discharge opening at all times. Pour one ounce 29 ml of oil through spark plug hole of this manual. Run engine at least 10 minutes after adding stabilizer to allow the stabilizer to reach the carburetor. Be sure to tion is if service has been performed on the gear case.
Be sure lever springs back and locks into desired position. Click to watch the video. Wait for all moving parts to stop. The bearings and bushings 8. If the belts are damaged or begin to slip from wear, they should 1. Thank you for using Manage my life. Spark plug wire is 8.
In Stock, 25+ Available The purpose of the 530069216 Tank Purge Line is to return the excess fuel that is in the carburetor after the primer bulb has been pushed. Try to start the engine as you normally do. Please check the fuel lines from inside the fuel tank to the outside and to the carburetor for cracks. Position chute rotater head over chute bracket. After you pull the rope, a few times remove the spark plug. Most of Poulan Pro's gas-powered, hand-operated tools, including trimmers, blowers and chainsaws, each has a two-cycle engine.
Exercise caution to avoid slipping or falling, especially or electric starting motors. Make sure the augers and all moving bolts. Be sure lever springs backoffers the best snow thrower performance. Be sure that all nuts, bolts, screws, and pins are securely 4. To do this you need a compression gauge. Run the machine a few minutes after throwing snow weights, counterweights, or cabs.
Pull recoil starter handle quickly. Skid plate - used to adjust height of scraper bar from the ground. Remove the two 2 screws securing the auger housing to the pallet. The unit tilted, resting on theof operation and replace if necessary. The only time the lubricant needs atten- 6. After the packed snow has been dislodged, return the clean-out tool to its mounting clip by pushing it into the clip. It has been designed, engineered and manu-factured to give best possible dependability and perfor- Gasoline Capacity 4.
Shut off engine and wait for all moving parts to stop. Connect spark plug wire to spark plug. Install the two 2 hex bolts and tighten securely. Place wire where it cannot come 1. The instructions willenable you to assemble and maintain your snow thrower Oil Capacity: 26 Ouncesproperly. Also, despite ordering late in the day, they shipped it out the same day! Connect the power cord to the engine.
Fuel shut-off valve if so 1. Do not overload the machine capacity by attempting such as hot water heaters, space heaters, or clothes to clear snow at too fast a rate. It is supplied directly from original equiplement manufacturer. WaterChange the oil after every 25 hours of operation or at least once in engine can result in shortened engine life. Have a dry cloth handy to hold the filter and catch any dripping fuel. Be sure lever springs back and locks into desired position.
Lubricate as shown in the Maintenance section of this 3. Note: If the fuel line is cracking, replace fuel line to ensure no leaks, fuel line will break down over time due to the elements. Do not safety glasses or eye shields while operating use to start a warm engine. Your new snow thrower has been assembled at the factory with the exception of those parts left unassembled for shippingpurposes. This bag into ignition slot until it clicks. Four-cycle engines -- which are most often used in gas-powered lawnmowers -- also need oil, but it is not mixed with gasoline. Remove when snow thrower is not in use.
Overall I had a great experience dealing with them and I will look to them for other needs in the future! Position the electric starter switch on the switch bracket and reinstall the mounting screws. Failure to do so can cause the unitto malfunction and pose a risk of injury to the operator. The origins of the Poulan Pro line of landscaping and gardening equipment date to 1944. Your snow thrower engine is equipped with both a 120 VoltA. Look up your model to make sure you get the right parts for your snowblower. Use the correct tools as necessary to ensure proper tightness. Use the choke can result in severe eye damage.